Programming
Bennett HF H35 Instruction Manual
44
above.
Note
: If an error is made, press the correct number. The new
number replaces the error.
4.
Press [
ENTER]
to save setting and to advance to the next option. If
programming is complete, press [
CANCEL]
button to exit this menu
code.
NUMBER OF DETECTORS
This option is used to select the number of detectors used. This option is set
at the factory. The default setting will appear in the Main Display.
Note:
Add2
indicates a detector is present with Modbus Slave ID of 2 and Add3 indicates
a detector is present with Modbus Slave ID of 3.
0 = None (Default)
1 = Add2
2 = Add3
3=Both (For two gas detectors)
Once
Enter
has been pressed from the previous option, the number of
detectors will appear in the main display.
The default setting is set to 0-None indicating that no detector is present.
To change the default setting, use the numeric keypad to select the desired
option. Add2 indicates a detector is present with Modbus Slave ID of 2 and
Add3 indicates a detector is present with Modbus Slave ID of 3.
Note
: If an
error is made, press the correct number. The new number replaces the error.
Press [
ENTER]
to save setting and to advance to the next option. If
programming is complete, press [
CANCEL]
button to exit this menu code.
Press the [
CANCEL]
button to exit mode 7.
Figure 4.22
–
Number of Detectors
NOTE: To review or change the settings in Menu Code 7. Press the Enter button on the keypad. Each time you press
the Enter button the display cycles through the options in Menu Code 7.
MENU CODE 8
–
DECIMAL POINTS: MONEY, MASS, AND PPM DISPLAYS
The decimal point in the money display, mass display and the PPM display can be changed. Contact an authorized service
technician to change from gallons to liters. The dispenser is shipped from the factory set for the monetary system in the United
States.
NOTE: If the dispenser is to be operated in U.S. dollars, do NOT enter this Menu Code!
PROCEDURE TO CHANGE DECIMAL PLACEMENT:
1.
Press the
8
button and then the
[MODE]
button on the
keypad. The United States standard decimal placement
appears in the main displays and PPM display. The number 0
appears in the main display to show the dispenser is set for
U.S. Standard.
NOTE: There are seven decimal selections available. See
for a sample of the decimal display for each
selection. The price in Selection 0 is in dollars. The price
in Selection 6 is in cents.
2.
Use the
0
through
6
buttons on the keypad to enter a new
selection.
3.
Press the [
ENTER
] button. The new decimal placement
appears in the displays.
4.
If an error is made, repeat steps 1 and 2 until the correct
decimal placement selection appears.
5.
When the correct decimal selection is made, press the
[
ENTER
] button to save the selection.
Figure 4. 23
–
DECIMAL PLACEMENT
Sale $
d E t E C t
Kilograms
0
C O d E
7
Содержание HIGH FLOW H35
