Programming
Bennett HF H35 Instruction Manual
48
PROCEDURE
1.
Press the number
1
and
4
, then the [
MODE
]
button on the keypad. The PPM
display show the dispenser is in Menu Code 14.
If the dispenser has not been programmed since it came from the factory,
the display shows the Flash option. One is the default setting for the Flash
option.
2.
Press [
ENTER
] to cycle through each display option (Flash, Dash, Flip, and
Digits).
3.
To program a setting, use the
0
and
1
buttons on the keypad to enter a new
setting.
Note:
If an error is made, press the correct number. The new number
replaces the error.
4.
When the correct option appears in the main display, press the [
ENTER
]
button to save and cycle to the next available option.
5.
Press the [
CANCEL
] button to exit this menu code.
Figure 4.31 - Flash
MENU CODE 15
–
SELECT THE FLEET OPTION
This menu code (when enabled) will allow a price change after the pump handle has been turned on. This allows the dispenser
to be compatible with fleet systems for use in non-retail situations. The dispenser may not be compatible with the fleet system
interface if this option is not enabled. The fleet option is set as enabled as default.
Note:
The dispenser will operate (reset) without
any price being set in mode 4 or downloaded from a console.
OPTIONS
•
0
- The fleet option is
disabled
.
•
1
–
(Default) The fleet option is
enabled
.
PROCEDURE
1.
Press the number
1
and
5
, then the [
MODE
] button on the keypad. The PPV
display shows the dispenser is in Menu Code 15.
If the dispenser has not been programmed since it came from the factory,
the number 1 appears in the main display.
2.
To disable the fleet option, press the
0
button on the keypad.
Note:
If an
error is made, press the correct number. The new number replaces the error.
3.
When the correct option number appears in the main display, press the
[
ENTER
] button to save the selection.
4.
Press the [
CANCEL
] button to exit this menu code.
Figure 4.32
–
Disabled Option (DEFAULT)
MENU CODE 18
–
HOW TO CHANGE THE MONEY TOTALS CALCULATION METHOD
Menu Code 18 allows the manager to select the method for calculating money totals. The first method adds the value on the
display to the Money Totals and stores the amount. This Money Total matches the cash drawer total.
The second method stores the Money Total as it was calculated at delivery. No rounding - Cross multiplication method (Mass x
Price Per Mass). The Money Total is stored up to seven digits with five decimal places (only two are displayed). This method
results in higher accuracy of Money Totals. The options are as follows:
•
0
–
(Default) Sale money is rounded to nearest penny. Cash drawer method of calculation
.
•
1 - No rounding. Cross multiplication method of calculation (Mass x PPM).
Sale $
F L A s H
Kilograms
0
C O d E
1 4
Sale $
F L E E t
Kilograms
1
C O d E
1 5
Содержание HIGH FLOW H35
