Bartec Ex p Control Unit APEX Скачать руководство пользователя | Manualshive

Страница: 65 / 82

background image

Maintenance and care

Ex p Control Unit

SIEMENS Set

Page 64 of 80

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx

Rev. 0

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages.

10

Maintenance and care

Find out about the general safety instructions before starting
work (see Chapter 2.4 Safety instructions).

Carry out maintenance and care in accordance with the following sections,
unless otherwise agreed for customer-specific versions.

Types of purge gas

Only inert gas (e.g. nitrogen) or purified and dry instrument air is permitted as
purge gas. In any case, a filter must be installed upstream if the quality with
regard to foreign particles is not guaranteed. The following quality
characteristics of the purge gas should be met:

Residual dust: < 40 µm

Residual water: dew point +3 °C

Residual oil content: 1 mg/m³

Maintenance work

Maintenance intervals

MAINTENANCE INTERVALS

Maintenance according to the following maintenance schedule is
recommended in the case of proper operation, observing the
installation instructions and ambient conditions.

ATTENTION

MAINTENANCE AND CARE



The currently applicable regulations and the national provisions must
be observed for maintenance, service and inspection of the
equipment!



Operation and maintenance work may be performed by trained
specialist personnel only. The statutory regulations and the other
binding directives on occupational health and safety, accident
prevention and environmental protection must be observed.



When opening covers or removing parts, unless possible by hand, live
parts may be exposed. Connecting parts may also be live.

Maintenance interval

Work to be performed

Monthly

Visual inspection according to Chapter 10.2.2

Semi-annually

Cleaning according to Chapter 10.2.3

Annually

Regular maintenance according to Chapter 10.2.4

«
...
63
64
65
66
67
...
»

Содержание Ex p Control Unit APEX



















































































Отзывы:

Нет отзывов

Похожие инструкции для Ex p Control Unit APEX

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: GE Страницы: 2

Бренд: XOXO Modular Страницы: 13

Бренд: Saitek Страницы: 13

Бренд: Balboa Water Group Страницы: 28

Бренд: UE Страницы: 4

Бренд: GE Страницы: 425

Бренд: Wave Italy Страницы: 16

Бренд: TA Hydronics Страницы: 14

Бренд: Wavelink Страницы: 69

Бренд: BADODOSECURITY Страницы: 8

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

Бренд: L-Acoustics Страницы: 20

Бренд: Paradox Страницы: 3

Бренд: asalvo baby Страницы: 84

Бренд: GEM Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды