background image

Ex p Control Unit 

SIEMENS Set 

Commissioning 

 

Rev. 0 

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx 

Page 59 of 80  

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages. 

 

“K2 / K3 / K4“ relay setting 

 

ATTENTION 

ATTENTION WHEN SWITCHING PARAMETER K2 WITH K1  
When using relay K2 as enable relay (parameter K1), further selected 
parameters will not be used because relay K2 is seen as enable relay in this 
moment (SIL relevant) 

 

Assign messages to the signal relays K3 and K4 

 

The switching points can be assigned 
to the relays K2, K3 and K4 in the 
“Extended / Relay“ menu; multiple 
selection is possible. 

Where messages have a “minus 
sign“, this shows that the relay is 
activated if the value falls short. 

Where messages have a “plus sign“, 
this shows the relay is activated if the 
value is exceeded. 

 
 
 

 

Procedure: 

 

Connect computer with Ex p control unit  

 

Activate programming switch 

 

Log in to the WEB interface with the user level  

 

Select Extended / Relay menu 

 

In the “of the respective relay“ column, activate the specific message/s 
by clicking on the corresponding button. 

 E.g. click on the “K1“ button. The button alters from   to   

 

Confirm pop-up window with altered value  

 

Deactivate programming switch  

 

Содержание Ex p Control Unit APEX



















































































Отзывы: