Bartec Ex p Control Unit APEX Скачать руководство пользователя страница 71

Страница: 71 / 82

Maintenance and care

Ex p Control Unit

SIEMENS Set

Page 70 of 80

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx

Rev. 0

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages.

Status

Code

Plain text

00000014

Sensor error 3

External temperature sensors 1-3.
Error is only shown if the sensors are active.

00000015

p1 has not been reached

The setpoint p1 “Minimum pressure“ has not been reached.

00000016

p3 has not been reached

The setpoint p3 “Purge pressure“ has not been reached.

00000017

p4 exceeded

The setpoint p4 “Maximum pressure - operation“ is exceeded.

00000018

p5 exceeded

The setpoint p5 “Maximum pressure– purge“ is exceeded.

00000019

Temperature sensor 1 exceeded

The setpoint temperature at sensor 1 is exceeded.

0000001A

Temperature sensor 2 exceeded

The setpoint temperature at sensor 2 is exceeded.

0000001B

Temperature sensor 3 exceeded

The setpoint temperature at sensor 3 is exceeded.

Содержание Ex p Control Unit APEX



















































































Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Бренды по названию

Популярные бренды

Bartec Ex p Control Unit APEX, Руководство пользователя

Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Бренды по названию

Популярные бренды