Bartec Ex p Control Unit APEX Скачать руководство пользователя

Страница: 24 / 82

Ex p Control Unit

SIEMENS Set

Transport and storage

Rev. 0

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx

Page 23 of 80

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages.

Transport and storage

Scope of delivery

Missing parts or damage must be reported immediately in writing
to the forwarding agent, the insurance company or BARTEC
GmbH.

Check the completeness of the scope of delivery using the delivery note.

As standard, each Ex p control unit is delivered with the following scope of
delivery:

Set SIEMENS

7MB8000-7CA

7MB8000-7CB

Ex p Control Unit APEX,
Type: 07-37A2-3211/2726

Ex Control Station,
Type: 07-3103-2512/0639

p-Operator Panel,
Type: 17-51P5-1111

Set connection cable

LAN programming cable

Parameter switch

Packaging

The Ex p control unit is delivered packed in film, on pallets and/or in boxes.

Dispose of the packaging materials at the designated disposal points.
Observe the applicable national regulations for disposal.

Содержание Ex p Control Unit APEX



















































































Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Похожие инструкции для Ex p Control Unit APEX

Бренды по названию

Популярные бренды

Bartec Ex p Control Unit APEX, Руководство пользователя

Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Похожие инструкции для Ex p Control Unit APEX

Бренды по названию

Популярные бренды