Bartec Ex p Control Unit APEX Скачать руководство пользователя страница 64

Страница: 64 / 82

Ex p Control Unit

SIEMENS Set

Function check and sequence

Rev. 0

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx

Page 63 of 80

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages.

Function check and sequence

Safety during operation

DANGER

DEATH OR SERIOUS BODILY INJURY DUE TO DAMAGED EXPLOSION PROTECTION
MEASURE.

It is no longer possible to operate the control unit safely.

Danger of explosion



Put APEX control unit out of operation and ensure that it is not restarted.

Function flow diagram of the Ex p control unit

The operation of a pressurized device can be divided into three phases.

Flow diagram of the Ex p control unit

The Ex p control executes the following sequence during commissioning:

Activation

Safety state

- Ex p Control Unit

Pre-Purge-

Condition fullfilled

Purge time

counts down

Ex p Equipment

in Ex safe state

Parameter mode

- Pre pressure exceeded

(p1)

- Flow

Reached (p3)

- Countdown

ready

p1 pressure drop

p4 pressure exceede

Electronic failure

- Active parameter switch

Operating flow

Содержание Ex p Control Unit APEX



















































































Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Бренды по названию

Популярные бренды

Bartec Ex p Control Unit APEX, Руководство пользователя

Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Бренды по названию

Популярные бренды