Bartec Ex p Control Unit APEX страница 9 Скачать руководство пользователя

Страница: 9 / 82

About these operating instructions

Ex p Control Unit

SIEMENS Set

Page 8 of 80

01-37A2-7D0004_SIEMENS_Manual_Exp-Control-Unit_20220216_0_en.docx

Rev. 0

Disclaimer: We reserve the right to make technical changes. Changes, errors and printing errors do not justify claims for damages.

Highlighting in the document

Warnings

Warnings are used in this user manual to warn of property damage and personal
injury.



Always read and follow these warnings.

Warnings are specially highlighted in this user manual and identified by symbols:

DANGER

DANGER indicates a hazardous situation which, if safety measures are not
observed, may result in death or serious injuries with permanent damage.

WARNING

indicates a hazardous situation which, if safety measures are not

observed, may result in serious injuries without permanent damage.

CAUTION

indicates a hazardous situation which, if safety measures are not

observed, can result in minor injuries.

ATTENTION

ATTENTION indicates a hazardous situation which, if the safety measures
are not observed, may result in damage to property.

Explanation of the structure of a warning notice

WARNING WORD

Identifies the source of danger, cause of danger or type of danger
Consequence of non-compliance with the described safety measure.



Safety measure

Example of a warning notice

DANGER

Operation of the control unit in the case of damage!
Death or serious injury.



Put the control unit out of operation and secure it against restart.

Содержание Ex p Control Unit APEX



















































































Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Похожие инструкции для Ex p Control Unit APEX

Бренды по названию

Популярные бренды

Bartec Ex p Control Unit APEX, Руководство пользователя

Результаты поиска

Содержание Ex p Control Unit APEX

Отзывы:

Похожие инструкции для Ex p Control Unit APEX

Бренды по названию

Популярные бренды