Bale Band-It GFC 100 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 108

background image

Operator’s Manual 77

- Check that a foreign object is not preventing the Right Band Full cylinder from
extending.
- Electric power or hydraulic power or hydraulic return has been disconnected or
shut off from machine.
- Remove and observe all 4 Band Position check valves. If the snap ring in the
bottom of the check valve is missing then the check valve needs to be replaced. If
you are unable to push the plunger from the end of the check valve in and it
spring back, then the check valve needs to be replaced.

- If the Right Band Full cylinder is still retracted,

- Check that hydraulic power is still on to the machine and that return line is still
connected.
- Check that a foreign object is not preventing the Right Band Full cylinder from
extending.
- Remove and observe all 4 Band Position check valves. If the snap ring in the
bottom of the check valve is missing then the check valve needs to be replaced. If
you are unable to push the plunger from the end of the check valve in and it
spring back, then the check valve needs to be replaced.
- Check that the directional valve is not stuck.

066 Timer Delay Error

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.

067 Communication from Band Computer

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait
approximately 10 seconds and then reinstall the two 10 amp fuses at the same time.
Recheck number on Line 3 after the dash, it should then be 1. Apply hydraulics.

«
...
80
81
82
83
84
...
»

Содержание GFC 100













































































































Отзывы:

Нет отзывов

Похожие инструкции для GFC 100

Бренд: OMCA Страницы: 36

Бренд: Salford Страницы: 64

Бренд: CAMPAGNOLA Страницы: 4

Бренд: Gardena Страницы: 8

Бренд: GARANT Страницы: 239

Бренд: p-light Страницы: 36

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Бренд: M-Audio Страницы: 25

Бренд: Feniex Страницы: 5

Бренд: PALAZZANI Страницы: 131

VEX-WPCR Series

Бренд: Exitronix Страницы: 4

ADVANTAGE 78400-117

Бренд: Medivators Страницы: 12

CAPE HORN EC202B

Бренд: SMP Playgrounds Страницы: 22

INTIMIDATOR 15XPC

Бренд: Bandit Страницы: 112

Бренд: Salvis Страницы: 28

Бренд: AGI Страницы: 33

Бренд: Air Techniques Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды