Bale Band-It GFC 100 Скачать руководство пользователя страница 29

Страница: 29 / 108

Operator’s Manual 24

Monthly Maintenance – 250 hours

Wheels & Lugs

Tighten lugs on wheels
Torque = 85 – 100 ft-lb (115.24 - 135.58 N-m)

Lower chrome rail bolts

Located on Bale Band-It Parts Section 120 Page 8
Check tightness of bolts

Horizontal plunger roller nuts

Located on Bale Band-It Parts Section 130 Page 1
Check tightness of bolts

Yearly Maintenance

Hydraulic oil

Due to viscosity breakdown, change hydraulic oil once a year.

Vertical Plunger gear & rack clearance Check

Gear and rack clearance needs to be between 0.020 inch (0.51 mm) min – 1/16 inch (1.6
mm) max.

If gear and rack clearance is greater than 1/16 inch (1.6 mm) then the gear can jump a
tooth and cause the vertical plunger to be out of time. Also significant wear on the upper
portion of rack will result if gear and rack are not tight.

Significant wear on wear strips can cause gear rack clearance to be too great. If wear is the
issue, replace and then check the measurement.

Содержание GFC 100













































































































Результаты поиска

Содержание GFC 100

Отзывы:

Bale Band-It GFC 100, Руководство оператора, Страница: 29 / 108

Результаты поиска

Содержание GFC 100

Отзывы: