Bale Band-It GFC 100 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 108

background image

Operator’s Manual 9

Hooking Up

The Bale Band-It is connected to the baler hitch. All baler chute extensions must be taken off
the baler. The center of the pin hole in the baler hitch needs to be adjusted 8-10 inches
(20 cm – 25 cm) from the main chamber of the baler.

GFC provides all electrical cables and connectors needed for operation.

The 10’ (3 m) electrical cable (10 gauge, 3 conductor) with terminal ends is to be attached to
a 12-volt DC power supply (battery of tractor). This cable consists of 3 separate insulated
wires. The black and white wires are to be attached to the +12-volt DC and the green wire is
to be attached to the –12-volt DC.

GFC does not provide the two hydraulic hoses that are to be attached onto the baler. These
hydraulic hoses go from the tractor to the Bale Band-It and must be 1 inch (25.4 mm) ID
hoses. Anything less than 1 inch (25.4 mm) ID will not allow proper hydraulic flow to the
machine and will slow performance. It is recommended that 1 inch (25.4 mm) male pipe
thread ends be crimped on one end of each of the two hoses mounted on the baler. This will
allow for the provided couplers to be attached to the hoses.

GFC provides one set of 1 inch (25.4 mm) pipe thread male/female couplers. These couplers
are to be used to connect to the existing hydraulic couplers located on the front chute of the
machine to the hoses mounted on the baler.

An additional set of 1 inch (25.4 mm) pipe thread male/female couplers can be purchased
from GFC to provide an easy connection from baler hose return to tractor reservoir.

«
...
12
13
14
15
16
...
»

Содержание GFC 100













































































































Отзывы:

Нет отзывов

Похожие инструкции для GFC 100

Бренд: Zenbooth Страницы: 60

Бренд: KBT Страницы: 12

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: Haag-Streit Страницы: 16

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Frontier FC5706

Бренд: OHAUS Страницы: 47

Бренд: Ocutech Страницы: 4

Бренд: Raytec Страницы: 60

Бренд: KAM Страницы: 5

Бренд: Warner Electric Страницы: 14

Бренд: Grundig Страницы: 19

Бренд: Megger Страницы: 12

Бренд: Tecsis Страницы: 52

Бренд: Stone Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды