Bale Band-It GFC 100 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 108

background image

Operator’s Manual 82

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait
approximately 10 seconds and then reinstall the two 10 amp fuses at the same time.
Recheck number on Line 3 after the dash, it should then be 1. Apply hydraulics.

079 Communication from Band Computer

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait
approximately 10 seconds and then reinstall the two 10 amp fuses at the same time.
Recheck number on Line 3 after the dash, it should then be 1. Apply hydraulics.

080 Communication from Band Computer

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait
approximately 10 seconds and then reinstall the two 10 amp fuses at the same time.
Recheck number on Line 3 after the dash, it should then be 1. Apply hydraulics.

081 Communication from Band Computer

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait
approximately 10 seconds and then reinstall the two 10 amp fuses at the same time.
Recheck number on Line 3 after the dash, it should then be 1. Apply hydraulics.

082 Communication from Band Computer

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait
approximately 10 seconds and then reinstall the two 10 amp fuses at the same time.
Recheck number on Line 3 after the dash, it should then be 1. Apply hydraulics.

083 Communication from Band Computer

- Disengage hydraulic power and unplug main power cord. Wait for approximately 10
seconds, plug back in and engage hydraulic power.
- On Line 3 of Display Monitor, if the number after the dash is 0, then disconnect main
electrical and hydraulic power. Open the plastic computer box in the banding box and
unplug the two 10 amp fuses. Reconnect main electrical power only. Wait

«
...
85
86
87
88
89
...
»

Содержание GFC 100













































































































Отзывы:

Нет отзывов

Похожие инструкции для GFC 100

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: LANGER EMV-Technik Страницы: 25

Electric Clamshell CSE12-208VCD

Бренд: Lang Страницы: 16

Brillion 3631-25

Бренд: Landoll Страницы: 138

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 64

Бренд: M-Audio Страницы: 16

Бренд: M-Audio Страницы: 4

Бренд: M-Audio Страницы: 52

Бренд: YASKAWA Страницы: 40

RAISED GARDEN BED

Бренд: Yardfully Страницы: 2

Бренд: Keithley Страницы: 57

Бренд: ZAMST Страницы: 14

Бренд: Future Artist Страницы: 42

Aesculap S4 Cervical

Бренд: B. Braun Страницы: 43

Dynamique Biski

Бренд: Enabling Technologies Страницы: 44

KONTROL KUBE ABACUS

Бренд: FIBERLOCK Страницы: 8

Бренд: Gronomics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды