Baldor VS1GV21-1B, Инструкция по установке и эксплуатации

Страница: 87 / 204

Parameter Descriptions 7-9 MN765
Block Title Parameter (Number)
Selection (Value)
Parameter Name and Description
OUTPUT
SETUP
(Continued)
OVERLOAD SET PT (1508) Preset Value: 150.0
Range: 0.0 - 200.0%
Sets the motor current value as a percent of drive rated current at which the
Overload digital output is active.
UNDERLOAD SET PT (1509) Preset Value: 50.0
Range: 0.0 - 200.0%
Sets the motor current value as a percent of drive rated current at which the
Underload digital output is active.
ANA OUT1 TYPE (1510) Preset Value: 0
Range: 0 - 3
0 to +10V (0) Sets the Analog Output Signal to 0 - 10V.
0 to 5V (1) Sets the Analog Output Signal to 0 - 5V.
4mA to 20mA (2) Sets the Analog Output Signal to 4 - 20mA.
0mA to 20mA (3) Sets the Analog Output Signal to 0 - 20mA.
ANA OUT2 TYPE (1513) Preset Value: 1
Range: 0 -1
+5/-5V (0) Sets the Output Signal ±5V.
+10/-10V (1) Sets the Output Signal ±10V.
ANA OUT1 SIGNAL (1511)
ANA OUT2 SIGNAL (1514)
Preset Value: 29
Preset Value: 3
Range: 0 - 34
Speed Ref (0) Scaled value of speed reference (input to velocity profiler) (ACC/DEC ramp).
Speed Demand (1) Scaled value of speed reference (output of velocity profiler) (ACC/DEC ramp).
ACC/DEC (2) Scaled value of ACC/DEC rate. Range is from 0 to max ACC/DEC rate.
Motor Current (3) Scaled value of Motor Current. Range is based on 2 times drive FLA. (Includes both
MAG and Load currents).
Mag Current (4) Scaled value of magnetizing current, range is based on 2 times drive FLA.
Mag Curr Cmd (5) The commanded D-axis PI vector magnetizing current to the current controller,
range is based on 2 times drive FLA.
Load Current (6) Scaled value of the load amps, range is based on 2 times drive FLA.
Load Curr Cmd (7) The commanded Q-axis PI vector load current to the current controller, range is
based on 2 times drive FLA.
Power Factor (8) Scaled value of power factor, range is from 0 to 1.0.
Ph1 Current (9) Scaled value of the phase 1 motor current, range is based on 2 times drive FLA.
Ph2 Current (10) Scaled value of the phase 2 motor current, range is based on 2 times drive FLA.
Ph3 Current (11) Scaled value of the phase 3 motor current, range is based on 2 times drive FLA.
Motor Voltage (12) Scaled value of the motor voltage, range is based on drive rated output voltage.
VD Demand (13) Flux controller output. Used to diagnose control problems.
VQ Demand (14) Load controller output. Used to diagnose control problems.
Bus Voltage (15) Scaled value of the Bus voltage. (Range is based on 123% of drive rated output
voltage).
Est. Abs Torque (16) Scaled value of the absolute torque, range is based on peak torque (2 x rated
torque).
Est. Torque (17) Scaled value of the motor torque (signed), range is based on rated torque (2 x rated
torque).
Control Temp (18) Scaled value of the control heatsink temperature, range is -50°C to 150ºC.
Analog In1 (19) Scaled value of the analog input 1 signal value.
Table 7-1 Level 1 Parameter Block Definitions Continued