Baldor VS1GV21-1B, Инструкция по установке и эксплуатации

Страница: 53 / 204

Control Wiring 5-23 MN765
5.5.16 Pulse Follower
Provides electronic gearing of two or more controls from an upstream pulse reference. This mode requires expansion board
EXBHH007 and its operation is described in MN755.
5.5.17 PLC
Provides control from a PLC device (Programmable Logic Control) as described in Chapter 10 of this manual. Preset speeds
are set in software. The opto inputs can be switches as shown in Figure 5-20 or logic signals from another device.
Figure 5-20 PLC Connection Diagram
1
2
3
4
5
6
7
Enable
J2
Digital Output 1 + (Collector)
Digital Output 1 - (Emitter)
Digital Output 2 + (Collector)
Digital Output 2 - (Emitter)
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Digital Input 5
Digital Input 6
Digital Input 7
Digital Input 8
8
17
9
10
11
12
13
14
15
16
18
19
20
Enable
See recommended tightening torques in Table A-2.
*
Optional
Inputs
J1
User Analog Return
Analog Input 1
Analog Ref. Power +
Analog Input 2 +
Analog Input 2 -
Analog Output 1
Analog Output 2
See Figure 5-4 for
connection information.
*Note: Remove factory jumper from J2-8 and J3-24 before connecting switch at J2-8.
One input must be a direction
input (FWD or REV).
5.6 Digital Outputs
Digital Outputs 1 and 2 are opto-isolated. Internal supply or a customer provided external power source may be used as
shown in Figure 5-21. The maximum voltage from Digital Output to common when active is 1.0 VDC.
If the Digital Outputs are used to directly drive a relay, a flyback diode rated at 1A, 100V (IN4002 or equivalent) minimum
should be connected across the relay coil. See Figure 5-21. Each opto output is programmed in the Output programming
block.
Figure 5-21 Digital Output Power Connections
Note: Digital Outputs are rated to 24VDC @ 60mA resistive (non-inductive).
Sinking Current Connections
Sourcing Current Connections
Internally Supplied 24VDC Externally Supplied 24VDC
Sinking Current Connections
Sourcing Current Connections
See recommended tightening torques in Table A-2.
J2
Digital Output 1 +
Digital Output 1 -
Digital Output 2 +
Digital Output 2 -
21
J3
Internal 24V Return
22
23
24
17
18
19
20
Out1
Out2
External User Return
External User +24V
In24V
User
24VDC
+
21
22
23
24
19
23
External User Return
External User +24V
In24V
Internal 24V Return
J2
17 Digital Output 1 + (Collector)
Digital Output 1 - (Emitter)
Digital Output 2 + (Collector)
Digital Output 2 - (Emitter)
18
19
20
21
J3
22
Out1
Out2
24
J2
Digital Output 1 +
Digital Output 1 -
Digital Output 2 +
Digital Output 2 -
21
J3
22
23
24
17
18
19
20
Out1
Out2
External User Return
External User +24V
In24V
Internal 24V Return
User
24VDC
+
J2
Digital Output 1 +
Digital Output 1 -
Digital Output 2 +
Digital Output 2 -
J3
Internal 24V Return
17
18
20
Out1
Out2
External User Return
External User +24V
In24V