Baker Hughes DigitalFlow XGF868i Скачать руководство пользователя страница 11

Страница: 11 / 100

Chapter 1. Programming site data

1.1 Introduction

The XGF868i flow transmitter must be properly installed

and programmed, as described in the

Startup guide

before it can provide accurate flow rate measurements.

After completing the installation and initial setup, use this

chapter to program the advanced features of the XGF868i

keypad program

Step-by-step programming instructions are presented in

this chapter. Also, as a programming aid, a complete set

of menu maps for the XGF868i are included in

Appendix A.

Menu Maps on page 39

. The specific figure numbers will

be referenced throughout this chapter, as required.
Refer to the appropriate section for a discussion of the

following

keypad program

features:

•

Channelx-ACTIV

- activate one or both channels

and scroll to the desired measurement method.

•

Channelx-SYSTM

- enter the individual channel

parameters.

•

Channelx-PIPE

- enter the pipe geometry and other

parameters.

•

Channelx-I/O

- set up the inputs and outputs.

•

Channelx-SETUP

- set the signal limits, response times

and mass flow status.

•

Global-SYSTM

- scroll to system units (English or metric).

•

Global-I/O

- set up error handling, option cards

and the display.

•

Global-COMM

- set the serial port parameters.

NOTE:

The “x” in CHx represents the channel number.

To get the XGF868i up and running as quickly as possible

you must, as a minimum, activate the channel(s), enter the

channel and global system data and the pipe parameters.

The

procedure options

section at the end of each menu will

help you in programming the required (quick startup) and

optional data.

NOTE:

In this manual, only the programming of channel 1 will

be described. To program channel 2 of a 2-channel meter,

simply repeat the same procedure presented for channel 1.

1.2 Programming methods

You can program the XGF868i via either the keypad on the

lower part of the glass window, or

PanaView™

, a PC-based,

non-resident software program that communicates with

the XGF868i via its RS232 serial port. PanaView supplements

basic XGF868i functions with several additional capabilities.

With PanaView, you can:
•  Load and save site file data
•  Create and save graph and log files
•  Display text output and graphs of live measurement data
•  Create custom templates for displaying text, graph and

log data

• Interface with multiple Panametrics instruments.

Although the actual displays differ somewhat, the general

procedures are the same for all three programming

methods. This chapter provides detailed programming

instructions for use with the magnetic keypad. If you

are using PanaView™, see

Appendix C. Programming

the XGF868i with PanaView on page 51

, and/or the

PanaView™ user’s manual

(910-211) for detailed instructions.

IMPORTANT

This manual is for instruments using software version

Y4AM or later.

Содержание DigitalFlow XGF868i





































































































Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды

Baker Hughes DigitalFlow XGF868i, Руководство по программированию

Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды