Baker Hughes DigitalFlow XGF868i Скачать руководство пользователя страница 5

Страница: 5 / 100

Information paragraphs

Note:

These paragraphs provide information that provides a

deeper understanding of the situation, but is not essential to

the proper completion of the instructions.

IMPORTANT:

These paragraphs provide information emphasizing

instructions which are essential to proper setup of the

equipment. Failure to follow these instructions carefully

may cause unreliable performance.

WARNING!

Indicates a potentially hazardous situation

which can result in serious personal injury or

death, if it is not avoided.

CAUTION!

Indicates a potentially hazardous situation

which can result in minor or moderate injury

to personnel or damage to the equipment, if

it is not avoided.

HIGH VOLTAGE!

This symbol indicates the presence of high

voltage. It calls your attention to situations or

operations that could be dangerous to you

and other persons operating the equipment.

Read these messages and follow the

instructions carefully.

Safety issues

WARNING!

It is the responsibility of the user to make sure

all local, county, state and national codes,

regulations, rules and laws related to safety

and safe operating conditions are met for

each installation.

Auxiliary equipment

Local safety standards

WARNING!

Auxiliary equipment may have both manual

and automatic modes of operation. As

equipment can move suddenly and without

warning, do not enter the work cell of this

equipment during automatic operation,

and do not enter the work envelope of this

equipment during manual operation. If you

do, serious injury can result.

Working Area

WARNING!

Make sure that power to the auxiliary

equipment is turned OFF and locked out

before you perform maintenance procedures

on the equipment.

Qualification of personnel

Make sure that all personnel have manufacturer-approved

training applicable to the auxiliary equipment.

Personal safety equipment

Make sure that operators and maintenance personnel have

all safety equipment applicable to the auxiliary equipment.

Examples include safety glasses, protective headgear,

safety shoes, etc.

Unauthorized operation

Make sure that unauthorized personnel cannot gain access

to the operation of the equipment.

Содержание DigitalFlow XGF868i





































































































Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды

Baker Hughes DigitalFlow XGF868i, Руководство по программированию

Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды