Azbil F4Q Скачать руководство пользователя страница 51

Страница: 51 / 76

6-5

Chapter 6. Communication Data

Item

Data range

/ [unit]

Data address

Decimal

(hexadecimal)

Notes

Number of the SP
currently in use

0–7

1205 (04B5)

✓



If “3” (SP No. switching) is set for C-10,
C-11, or C-12 (Digital input 1–3 function
assignment), the setting cannot be
changed by communication.

If writing is attempted, an error
response will be returned.

Value of the SP
currently in use

(0–100 % FS)

1206 (04B6)

✓

The value is without a decimal point. For
the number of decimal places and the
unit of data, see “Flow rate digits after
the decimal point” (address 1003) and
“Flow rate unit” (address 1005).

(0–100 % FS)

1207 (04B7)

✓

Valve manipulated
variable (MV)

0–1000 [× 0.1 %]

1208 (04B8)

✓

The value is without a decimal point.

Online SP

1209 (04B9)

✓

This SP is used if “2” (online SP) is set for
C-03, Flow rate setup method (SP setup
method selection).

Error

1210 (04BA)

✓

A code indicating the device status is
given for reference.

For an RS command, statuses are
expressed as decimal numbers.

Alarm

1211 (04BB)

✓

Warning

1212 (04BC)

✓

Information

1213 (04BD)

✓

Содержание F4Q













































































Результаты поиска

Содержание F4Q

Отзывы:

Бренды по названию

Популярные бренды

Azbil F4Q, Руководство пользователя

Результаты поиска

Содержание F4Q

Отзывы:

Бренды по названию

Популярные бренды