manualshive.com logo in svg

Azbil F4Q, Руководство пользователя

Поделиться
Скачать
Azbil F4Q Скачать руководство пользователя страница 18

4-2

 

„

Overview of a CPL Frame

A message consists of the following two layers. Both the instruction message from 

the master station and the response message from the slave station take this form.

•  Data link layer:

This layer contains the basic information required for communication. For 

example, it tells the destination of the message and the checksum information.

•  Application Layer:

Data is read and written in this layer. The content of the layer varies according to 

the purpose of the message.

Many slave stations

(up to 31 units)

Master station

Slave station

Instruction message from 

master station

Response message from

slave station

Application layer

Data link layer

Application layer

Data link layer

The driver in the data link layer has the following 

information:

  • The destination (the device address).

  • The check sheet for the shipment (the checksum).

The application layer cargo (data) 

changes every time according to 

the purpose of the operation.

Details on each layer are given in the next section.

4 - 2 

Message Structure

Содержание F4Q













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды