manualshive.com logo in svg

Azbil F4Q, Руководство пользователя

Поделиться
Скачать
Azbil F4Q Скачать руководство пользователя страница 42

5-8

Chapter 5.  Modbus Communication (RTU Mode)

 

„

Function 06 (one data write command)

Function 06 is the command for writing one data record.

The command and the normal response have the same format.

 Note

• 

 

„

 Error termination code (p. 5-4)

 (for details of error response)

 

z

Send command format

Frame structure

Number 

of bytes

Description

Address

1

Device address

Function

1

6 (0x06)

Data

Data address

2

Data address (upper byte 

→

 lower byte)

Data

2

Data to write (upper byte 

→

 lower byte)

CRC check

2

Check code (lower byte 

→

 upper byte)

 

z

Normal response format

The format is the same as the send command.

Examples:

Sent message: Write “1” (0x0001) to data address 2001 (0x07D1)

Device address

Function code

Data address

Data

CRC

01H

06H

07H

D1H

00H

01H

D5H

47H

Normal response:

Device address

Function code

Data size

Data

CRC

01H

06H

07H

D1H

00H

01H

D5H

47H

Error response:

Device address

Function code

Error termination 

code

CRC

01H

86H

02H

51H

32H

The function code when an error occurs (here, 86H) is obtained by flipping the 

most significant bit of the function code (0x06) to 1.

Содержание F4Q













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды