Azbil F4Q Скачать руководство пользователя страница 4

Страница: 4 / 76

Safety Precautions

CAUTION

Use this product within the operating conditions (for temperature, humidity, voltage,

vibration, shock, mounting orientation, atmosphere, etc.) given in the specifications in

Digital

Mass Flow Controller Model F4Q User’s Manual

(CP-UM-5978JECK).

Otherwise there is a danger of device failure.
Before wiring the device, turn the power off. Otherwise there is a danger of device failure.

Wire this device correctly by using the wiring method, power, and installation method

specified in this user’s manual. Otherwise there is a danger of device failure.

Do not allow wire clippings, metal shavings, water, etc., to enter the device. There is a danger

of device failure.

If there is a risk of a power surge caused by lightning, use a surge absorber (surge protector).

Otherwise there is a danger of fire or device failure.

Make sure that the wiring is correct before turning the power on. Incorrect wiring may result

in damage or malfunction.

Do not disassemble this device. There is a danger of device failure.

Do not apply excessive force to cables or connectors when connector cables or the AC adapter

is attached.

Doing so may damage the connector or circuit board.

Содержание F4Q













































































Результаты поиска

Содержание F4Q

Отзывы:

Бренды по названию

Популярные бренды

Azbil F4Q, Руководство пользователя

Результаты поиска

Содержание F4Q

Отзывы:

Бренды по названию

Популярные бренды