Avaya programming and use Скачать руководство пользователя страница 413 | Manualshive

Страница: 413 / 468

Avaya programming and use Скачать руководство пользователя страница 413

Troubleshooting

Problems with Manual Backup

11-23

Display Shows “Backup Failed:SystemBusy”
at Idle Extensions 10 and 11

1

1

Possible Cause: Changes were being made to system programming or central telephone
programming while a backup was in progress.

What to do: The backup is rescheduled for the next day at 2:00 a.m. Enter Backup
Programming—Automatic (#123) and select Option 3 to clear the alarm display (see

Backup-Failure Alarm” on page 11-4

).

Problems with Manual Backup

1

1

Display Shows “Insert Valid Card” in
System Programming Mode

1

1

Possible Cause: The system did not detect a valid Backup/Restore PC Card when you tried to do
a manual backup by using Backup Programming—Manual (#124).

What to do: Power down the system, insert a valid Backup/Restore PC Card in PC Card Slot 2 of
the PARTNER ACS processor module, and reapply power to the system. Restart the procedure.

Display Shows “Card is Write Protected” in
System Programming Mode

1

1

Possible Cause: You tried to do a manual backup by using Backup Programming—Manual
(#124), but the Backup/Restore PC Card in the PC Card slot is write-protected.

What to do: Using the end of a paper clip or another pointed object, gently push the write-protect
tab upward to the nonprotected position (see

Figure 11-1 on page 11-22

), and try the procedure

again. (You do not need to remove the card from the processor to slide the write-protect tab up.)

Display Shows “System Busy” in
System Programming Mode

1

1

Possible Cause: An automatic or manual backup was in progress at the time you requested a
manual backup.

What to do: Exit the procedure and retry the manual backup after a few minutes.

«
...
411
412
413
414
415
...
»

Содержание programming and use





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов