Avaya ERS 8600 series Скачать руководство пользователя

Страница: 164 / 420

Variable

Value

info

Displays OSPF range characteristics.

ipaddr

Specifies the address of an OSPF area. Use dotted
decimal notation to specify the area name.

ipv6addr-prefix

Configures the IPv6 address range of an OSPF area.
The string length is 0–255 characters.

Configuring OSPF area virtual interfaces

If a remote OSPF ABR uses no connection to the backbone area but needs to be part of the

same routing domain (AS) in which the switch resides, configure an OSPFv3 virtual interface

to the ABR.

You can use any value for the OSPFv3 area name (for example, 1.1.1.1 or 200.200.200.200).

Important:

OSPFv3 behavior is modified according to OSPFv3 standards so that OSPFv3 routes

cannot be learned through an area border router (ABR) unless the router connects to the

backbone or through a virtual link.

Procedure steps

Configure an OSPFv3 area virtual interface by using the following command:

config ipv6 ospf area

<ipaddr>

virtual-interface

<ipaddr>

Variable definitions

Use the data in the following table to use the

config ip ospf area virtual-

interface

command.

Variable

Value

create

Creates a virtual interface for an area.

dead-interval

<seconds>

Specifies the dead interval, in seconds, as a
range 1–4095.

delete

Deletes a virtual interface for an area.

IPv6 routing configuration using the CLI

164 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды