Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 60 / 420

background image

supports automatic allocation of reusable network addresses and of additional configuration

parameters.

To request the assignment of one or more IPv6 addresses, a client first locates a DHCP server

and then requests the assignment of addresses and other configuration information from the

server. The client sends a Solicit message to the All_DHCP_Relay_Agents_and_Servers

(FF02::1:2) multicast address to find available DHCP servers. Any server that can meet the

client's requirements responds with an Advertise message. The client then chooses one of the

servers and sends a Request message to the server asking for confirmed assignment of

addresses and other configuration information. The server responds with a Reply message

that contains the confirmed addresses and configuration.

IPv6 DHCP clients use link-local addresses to send and receive DHCP messages. To allow a

DHCP client to send a message to a DHCP server that is not attached to the same link, you

must configure a DHCP relay agent on the client's link to relay messages between the client

and server. The operation of the relay agent is transparent to the client.

A relay agent relays messages from clients and messages from other relay agents.

Remote ID

IPv6 DHCP Relay supports the Remote ID parameter (RFC 4649). When you enable Remote
ID on the switch, the relay agent adds information about the client to DHCPv6 messages before
relaying the messages to the DHCP server. The server can use the supplied information in the
process of assigning the addresses, delegated prefixes and configuration parameters that the
client is to receive.

The remote ID option contains two fields:

• enterprise-number

• remote-id

On the Ethernet Routing Switch 8800/8600, the enterprise-number (vendor ID) used is 1584
and the remote-id field is filled with the unique MAC address of the client.

IPv6 VRRP

For IPv6 hosts on a LAN to learn about one or more default routers, IPv6-enabled routers send

Router Advertisements using the IPv6 Neighbor Discovery (ND) protocol. The routers multicast

these Router Advertisements every few minutes.

The ND protocol includes a mechanism called Neighbor Unreachability Detection to detect the

failure of a neighbor node (router or host) or the failure of the forwarding path to a neighbor.

Nodes can monitor the health of a forwarding path by sending unicast ND Neighbor Solicitation

messages to the neighbor node. To reduce traffic, nodes only send Neighbor Solicitations to

neighbors to which they are actively sending traffic and only after the node receives no positive

indication that the neighbors are up for a period of time. Using the default ND parameters, it

takes a host approximately 38 seconds to learn that a router is unreachable before it switches to

IPv6 routing fundamentals

60 Configuration — IPv6 Routing

November 2010

«
...
58
59
60
61
62
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: 3xLogic Страницы: 2

Бренд: QNAP Страницы: 39

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

18x18 Card Cage

Бренд: WolfPack Страницы: 31

Бренд: Aethra Страницы: 2

Бренд: NETGEAR Страницы: 142

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Бренд: ADTRAN Страницы: 20

EdgeRouter ER-8

Бренд: Ubiquiti Страницы: 20

24-Port 1000BASE-T

Бренд: Comet Labs Страницы: 44

P-660R-F1 series

Бренд: ZyXEL Communications Страницы: 268

SECURE BOOT STICK FX

Бренд: Ecos Страницы: 22

ISDN Router ISDN

Бренд: Ringdale Страницы: 165

Бренд: Syris Страницы: 27

DES-1016D - Switch

Бренд: D-Link Страницы: 32

Amplifi DIR-657

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды