Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 73 / 420

background image

For a given SMLT VLAN RSMLT is supported for any of the following scenarios:

• IPv4 Only: IPv4 is configured on the VLAN and IPv6 is not. RSMLT operation and logic

remains unchanged from the current implementation.

• IPv6 Only: IPv6 is configured on the VLAN and IPv4 is not. IPv6 RSMLT operation follows

that of IPv4 as described in this document.

• IPv4 and IPv6: Both IPv4 and IPv6 are configured on the VLAN. IPv4 RSMLT operation

and logic remains unchanged from the current implementation and unaffected by IPv6.
IPv6 operation follows that of IPv4 as described in this document.

RSMLT network design and configuration

Because RSMLT is based on SMLT, all SMLT configuration rules apply. In addition, RSMLT is
enabled on the SMLT aggregation switches for each VLAN. The VLAN must be a member of
SMLT links and the IST trunk. For more information about configuring SMLT in a Layer 2
environment, see Avaya Ethernet Routing Switch 8800/8600 Configuration – Link Aggregation,
MLT and SMLT (NN46205-518).

The VLAN also must be routable (IP address configured) and an Interior Routing Protocol (IGP)
such as OSPFv3 must be configured on all four routers, although it is independent of RSMLT.
You can use any supported routing protocol, even static routes, with RSMLT.

RSMLT pair switches provide backup for each other. As long as one of the two routers of an
IST pair is active, traffic forwarding is available for both next hops R1/R2 and R3/R4.

Important:

Do not enable ICMP redirects on RSMLT VLANs. If you enable this option (using the

config

ipv6 icmp redirect-msg

command), RSMLT cannot function. The option is disabled

by default.

RSMLT-edge

RSMLT-edge stores the RSMLT peer MAC/IPv6 address pair in its local configuration file and
restores the configuration if the peer does not restore after a simultaneous reboot of both
RSMLT-peer switches.

The RSMLT-edge feature simply adds an enhancement whereby the peer's MAC (for the IP
on the VLAN) gets committed to the config.cfg file after a save config; that way if you power
off both switches, and then power up only 1 of them, that single switch can still take ownership
of its peer's IP on that VLAN even if it has not yet even seen that peer switch since it booted;
this is necessary as you might have configured the peer (the switch which is still down) IP as
the default gateway in end stations.

IPv6 RSMLT

Configuration — IPv6 Routing

November 2010 73

«
...
71
72
73
74
75
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

Бренд: D-Link Страницы: 267

Бренд: D-Link Страницы: 12

Бренд: IBM Страницы: 104

System Storage TS3100

Бренд: IBM Страницы: 375

Бренд: Draytek Страницы: 8

Бренд: FS Страницы: 19

Бренд: NC-link Страницы: 20

Бренд: Paradyne Страницы: 6

Бренд: ZyXEL Communications Страницы: 170

Бренд: Rajant Corporation Страницы: 40

Бренд: OneAccess Страницы: 47

Бренд: Billion Страницы: 158

Бренд: Axtrinet Страницы: 49

Бренд: Exibel Страницы: 2

iConverter GX/F

Бренд: Omnitron Systems Technology Страницы: 2

DSL906 1DA Series

Бренд: Aztech Страницы: 15

Бренд: Alcatel-Lucent Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды