Avaya ERS 8600 series Скачать руководство пользователя

Страница: 339 / 420

filter apply act <act-id>

Configuring ACLs

Configure access control lists (ACL) to create rules for the ACT.

Important:

If an ACT contains IPv6 attributes, you must configure an ACL of pktType IPv6. If the ACT

uses only Ethernet attributes, you can configure one ACL of pktType IPv4 and an ACL of

pktType IPv6.

Prerequisites

You must log on to the Global Configuration mode in the ACLI.

Procedure steps

1. Configure an ACL by using the following command:

filter acl <acl-id> type <inVlan|outVlan|inPort|outPort> act
<act-id> pktType <ipv4|ipv6> name <word>

2. Enable an ACL by using the following command:

filter acl <acl-id> enable

Variable definitions

Use the data in the following table to use the

filter acl

command.

Variable

Value

acl-id

Specifies an ACL ID in the range 1–4096.

act <act-id>

Specifies the ACT ID to associate with the ACL.

enable

Enables the ACL state along with all ACEs below it.
Enable is the default state for the ACL.

name

<word>

Renames an ACL. To configure this option to the
default value, use the default operator with the
command.

Configuring ACLs

Configuration — IPv6 Routing

November 2010 339

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды