Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 56 / 420

background image

Important:

Currently, 3DES is the only supported encryption algorithm for the Avaya Ethernet Routing

Switch 8800/8600. Proper functioning requires the 3DES encryption image.

The implementation of the SSH server on the Avaya Ethernet Routing Switch 8800/8600

enables the SSH client to securely connect to the Avaya Ethernet Routing Switch 8800/8600

and supports commercially available SSH clients.

Important:

You must use the CLI to initially configure SSH. You can use Enterprise Device Manager to

change the SSH configuration parameters. Avaya recommends that you use the console

port to configure the SSH parameters.

SSH version 2 (SSH-2)

SSH protocol, version 2 (SSH-2) is a complete upgrade of the SSH-1 protocol. While SSH-1
contains multiple functions in a single protocol, SSH-2 functions are divided among the
following three protocols:

• SSH transport layer (SSH-TRANS)

The SSH transport layer manages the server authentication and provides the initial
connection between the client and the server. When a connection is established, the
transport layer provides a secure, full-duplex connection between the client and the
server.

• SSH authentication protocol (SSH-AUTH)

The SSH authentication protocol runs on top of the SSH transport layer and authenticates
the client-side user to the server. SSH-AUTH defines three authentication methods: public
key, host-based, and password. SSH-AUTH provides a single authenticated tunnel for
the SSH connection protocol.

• SSH connection protocol (SSH-CONN)

The SSH connection protocol runs on top of the SSH transport layer and authentication
protocols. SSH-CONN provides interactive logon sessions, remote execution of
commands, forwarded TCP/IP connections, and forwarded X11 connections. These
services multiplex into the single encrypted tunnel provided by the SSH transport layer.

Figure 11: SSH version 2 protocols

on page 57 shows the SSH-2 protocols.

IPv6 routing fundamentals

56 Configuration — IPv6 Routing

November 2010

«
...
54
55
56
57
58
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 2

DSL-2540B - ADSL2/2+ Modem With EN Router

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 62

Бренд: Paradyne Страницы: 16

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 5

Nighthawk M6 Pro

Бренд: AT&T Страницы: 2

Бренд: process-informatik Страницы: 8

LinkSmart KW6515

Бренд: Kasda Страницы: 31

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: SyChip Страницы: 24

SmartNode 4520 Series

Бренд: Patton electronics Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды