virtual link. In an Ethernet Routing Switch 8800/8600, you can automatically create virtual links
or you can manually configure a virtual link.
Virtual linking is similar to backup redundancy. With virtual linking configured, the switch
creates a virtual link for vital traffic paths in your OSPF configuration if traffic is interrupted,
such as when an interface cable providing connection to the backbone (either directly or
indirectly) is disconnected from the switch. Automatic virtual linking ensures that a link is
created by using another switch.
If automatic virtual linking requires more resources than you want to expend, create manual
virtual links. Manual virtual links conserve resources and provide specific control over virtual
link placement in your OSPF configuration.
OSPF behavior is modified according to OSPF standards so that OSPF routes cannot be
learned through an ABR unless it connects to the backbone or through a virtual link.
Procedure steps
1. In the navigation tree, open the following folders: Configuration, IPv6.
2. Double-click
OSPF
.
3. Click the
Virtual If
tab.
4. Click
Insert
.
5. In the
AreaId
box, specify the area ID for the transit area.
The transit area is the common area between two ABRs.
6. In the
Neighbor
box, specify the neighbor ID.
The neighbor ID is the IP router ID of the ABR through which the other ABR must
route traffic destined for the backbone.
7. Click
Insert
.
8. To verify that the virtual link is active, refresh the Virtual If tab and check the
State
column.
If the state is point-to-point, the virtual link is active. If the state is down, the virtual
link is configured incorrectly.
Variable definitions
Use the data in the following table to configure the virtual link.
Variable
Value
AreaId
A read-only field indicating the transit area ID that the virtual link
traverses.
Neighbor
A read-only field indicating the router ID of the virtual neighbor.
Creating a virtual link
Configuration — IPv6 Routing
November 2010 149
Содержание ERS 8600 series
