Avaya ERS 8600 series Скачать руководство пользователя

Страница: 331 / 420

Adding an ACE with IPv6 header attributes

Add an ACE with IP header attributes as match criteria.

Important:

Be aware of the following:

• You cannot select (*) after <ace-op>.
• If you select no entry, You delete the Ethernet, ARP, or IPv6 protocol node.

Procedure steps

Add an ACE with IPv6 header attributes by using the following command:

config filter acl

<acl-id>

ace

<ace-id>

ipv6

Variable definitions

Use the data in the following table to use the

config filter acl ace ipv6

command.

Variable

Value

ace-id

Specifies an ACE ID in the range 1–1000.

acl-id

Specifies an ACL ID in the range 1–4096.

delete

<ipv6-attributes>

Deletes the specified IPv6 ACE attributes.

dst-ipv6 <ace-op>

<dst-ipv6-list>

Specifies the following:

• an operator for a field match condition (eq)

• the list of destination IPv6 addresses separated by

commas

info

Displays the current level parameter setting and the
next level directories.

nxt-hdr <ace-op> <nxt-hdr>

Specifies the following:

• an operator for a field match condition (eq | ne)

• the next header value

src-ipv6 <ace-op>

<src-ipv6-list>

Specifies the following:

Adding an ACE with IPv6 header attributes

Configuration — IPv6 Routing

November 2010 331

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды