Avaya ERS 8600 series Скачать руководство пользователя

Страница: 368 / 420

Configuring OSPFv3

Procedure steps

1. Configure VLAN 2 and add port members.

For IPv6, configure port-based or protocol-based VLANs. For this example, create

port-based VLAN 2:

ERS8600-B:5#

config vlan 2 create byport 1

ERS8600-B:5#

config vlan 2 ports add 3/1

2. Configure and enable the IPv6 address on VLAN 2:

ERS8600-B:5#

config vlan 2 ipv6 create addr

2001:100:102:202::1/64

ERS8600-B:5#

config vlan 2 ipv6 admin enable

3. Enable OSPFv3 on VLAN 2:

ERS8600-B:5#

config vlan 2 ipv6 ospf create 0.0.0.0

ERS8600-B:5#

config vlan 2 ipv6 ospf admin-status enable

4. Configure brouter port 7/1 with IPv6:

ERS8600-B:5#

config ethernet 7/1 ipv6 create addr

2001:100:102:201::1/64 vlan 3999

ERS8600-B:5#

config ethernet 7/1 ipv6 admin enable

5. Enable OSPFv3 on brouter port 7/1:

ERS8600-B:5#

config Ethernet 7/1 ipv6 ospf create 0.0.0.0

ERS8600-B:5#

config ethernet 7/1 ipv6 ospf admin-status

enable

By default, IPv6 router discovery is enabled. Any IPv6 device connected to VLAN 2 discovers

the 2001:100:102:202::1 address belonging to ERS8600-B. Verify the discovery by using the

following command:

ERS8600-B:5# config vlan 2 ipv6 nd info

Verifying operations from ERS 8600-A

The following commands verify that ERS 8600-A is learning routes from ERS 8600-B.

IPv6 CLI configuration

368 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды