Avaya ERS 8600 series Скачать руководство пользователя

Страница: 277 / 420

config ipv6 tunnel

<tunnel id>

create local-addr

<remote ipv4 address>

ipv6 addr

<remote ipv6 address/prefix length>

remote-address

<source ipv4

address>

Variable definitions

Use the data in the following table to use the

config ipv6 tunnel

command.

Variable

Value

create [local addr

<value>

]

[ipv6addr

<value>

] [remote-

address

<value>

]

Creates the tunnel for a VLAN or brouter port.

• local addr

<value>

configures the address for the

local device.

• ipv6addr

<value>

configures the local address for

the tunneled device in IPv6/prefix-length format.

• remote-address

<value>

configures the address for

the device that is tunneled to in IPv4 or IPv6/prefix-
length format.

delete

Deletes the tunnel.

hop-limit

<value>

Configures the maximum number of hops that a
packet can make before it is dropped.

value

is in the range 0–255.

info

Displays the current settings for the command.

tunnel id

Specifies the ID number of the tunnel in the range of
1-5000.

Example of configuring manual tunnels

Procedure steps

1. Configure the tunnel at the source.

ERS-8610:5#config ipv6 tunnel 1044 create local addr

20.10.10.107 ipv6addr

0100:0200:0300:0004:0005:0006:0000:aa01/80 remote-address

10.20.20.105

2. Configure the tunnel at the destination.

ERS-8610:5#config ipv6 tunnel 1045 create local addr

10.20.20.105 ipv6addr

0100:0200:0300:0004:0005:0006:0000:aa02/80 remote-address

20.10.10.107

Configuring manual tunnels

Configuration — IPv6 Routing

November 2010 277

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды