Avaya ERS 8600 series Скачать руководство пользователя

Страница: 318 / 420

Procedure steps

1. In the navigation tree, open the following folders:

Configuration, Security, Data

Path

2. Double-click

Advanced Filters (ACE/ACLs)

3. Click the

ACL

tab.

4. Select an IPv6 ACL.
5. Click

ACE

6. From the ACE Common tab, select an ACE.
7. Click

IPv6

8. Click the Destination Address tab.
9. Click

Insert

10. Specify the operation (the only option is eq [equals]) and the IPv6 addresses.

11. Click

Insert

Variable definitions

Use the data in the following table to configure the Destination Address tab.

Variable

Value

AclId

Specifies the ACL ID.

AceId

Specifies the ACE ID.

Oper

Select eq to specify IPv6 addresses equal to the addresses
included in the List field.

List

Type a single IPv6 address, range of IPv6 addresses, or
multiple IPv6 addresses.

Configuring an IPv6 next header rule for an ACE

Configure an ACE IPv6 next header so that the filter looks for a packets with the next header

parameter set.

Prerequisites

• The associated ACL packet type must be IPv6.
• The associated ACT IPv6 attributes must be nxtHdr.

IPv6 traffic filter configuration using Enterprise Device Manager

318 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды