AudioCodes Media Pack MP-11x Скачать руководство пользователя страница 462 | Manualshive

Страница: 462 / 650

background image

User's Manual

462

Document #: LTRT-65432

MP-11x & MP-124

3.

Configure the test endpoint parameters as desired. See the table below for a
description of these parameters.

4.

Click

Submit

to apply your settings.

Test Call Table Parameters

Parameter

Description

General Tab

Endpoint URI

[Test_Call_Endpoin
tURI]

Defines the endpoint's URI. This can be defined as a user or user@host.
The device identifies this endpoint only by the URI's user part. The URI's
host part is used in the SIP From header in REGISTER requests.

The valid value is a string of up to 150 characters. By default, this parameter
is not configured.

Called URI

[Test_Call_CalledU
RI]

CLI: called-uri

Defines the destination (called) URI (user@host).

The valid value is a string of up to 150 characters. By default, this parameter
is not configured.

Route By

[Test_Call_DestTyp
e]

Defines the type of routing method. This applies to incoming and outgoing
calls.



[0]

GW Tel2IP = (Default) Calls are matched by (or routed to) an SRD

and Application type (defined in the SRD and Application Type
parameters below).



[1]

IP Group = Calls are matched by (or routed to) an IP Group ID.



[2]

Dest Address = Calls are matched by (or routed to) an SRD and

application type.

Notes:



For REGISTER messages, the option

[0]

cannot be used as the routing

method.



For REGISTER messages, if option

[1]

is used, only Server-type IP

Groups can be used.

IP Group ID

[Test_Call_IPGroup
ID]

Defines the IP Group ID to which the test call is sent or from which it is
received.

Notes:



This parameter is applicable only if option

[1]

is configured for the 'Route

By' parameter.



This IP Group is used for incoming and outgoing calls.

Destination Address

[Test_Call_DestAd
dress]

Defines the destination host. This can be defined as an IP address

[:port

] or

DNS name

[:port

].

Note:

This parameter is applicable only if the 'Route By' parameter is set to

[2]

(Dest Address).

Destination
Transport Type

[Test_Call_DestTra
nsportType]

Defines the transport type for outgoing calls.



[-1]

Not configured (default)



[0]

UDP



[1]

TCP



[2]

TLS

Note:

This parameter is applicable only if the 'Route By' parameter is set to

[2]

(Dest Address).

Application Type

[Test_Call_Applicat
ionType]

Defines the application type for the endpoint.



[0]

GW & IP2IP (default)

«
...
460
461
462
463
464
...
»

Содержание Media Pack MP-11x











































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Pack MP-11x

Бренд: ABB Страницы: 44

Бренд: ECKELMANN Страницы: 34

Бренд: Vanguard Страницы: 74

Бренд: NeoGate Страницы: 37

Бренд: Net2Phone Страницы: 23

Бренд: Moxa Technologies Страницы: 6

Бренд: System Sensor Страницы: 10

Touchstone TG1652

Бренд: Arris Страницы: 44

GW-DLMS-485-ELSA15

Бренд: MARCOM Страницы: 13

Бренд: Grandstream Networks Страницы: 32

Бренд: Ubee Страницы: 99

NI WSN C Series

Бренд: National Instruments Страницы: 16

Бренд: THOMSON Страницы: 710

Бренд: MCK Страницы: 18

Бренд: Advantech Страницы: 78

Бренд: Odin TeleSystems Страницы: 36

Бренд: 2Wire Страницы: 30

HomePortal 3801HGV

Бренд: 2Wire Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды