AudioCodes Media Pack MP-11x Скачать руководство пользователя страница 240 | Manualshive

Страница: 240 / 650

background image

User's Manual

240

Document #: LTRT-65432

MP-11x & MP-124

Parameter

Description

Serving IP Group ID

[TrunkGroupSettings_ServingIP
Group]

Assigns an IP Group to where INVITE messages received from
this Hunt Group are sent. The actual destination to where these
INVITE messages are sent is according to the Proxy Set ID
associated with the IP Group. The Request-URI host name in
the INVITE and REGISTER messages (except for 'Per Account'
registration modes) is set to the value of the 'SIP Group Name'
parameter configured in the IP Group table (see 'Configuring IP
Groups' on page

Notes:



If this parameter is not configured, the INVITE messages are
sent to the default Proxy or according to the Tel to IP
Routing (see 'Configuring Tel to IP Routing' on page



If the PreferRouteTable parameter is set to 1 (see
'Configuring Proxy and Registration Parameters' on page

), the routing rules in the Outbound IP Routing table take

precedence over the selected Serving IP Group ID.

Gateway Name

[TrunkGroupSettings_GatewayN
ame]

Defines the host name for the SIP From header in INVITE
messages and for the From/To headers in REGISTER requests.

Note:

If this parameter is not configured, the global parameter,

SIPGatewayName is used.

Contact User

[TrunkGroupSettings_ContactUs
er]

Defines the user part for the SIP Contact URI in INVITE
messages and for the From, To, and Contact headers in
REGISTER requests.

Notes:



This parameter is applicable only if the 'Registration Mode'
parameter is set to 'Per Account' and registration through the
Account table is successful.



If registration fails, the user part in the INVITE Contact
header is set to the source party number.



The 'Contact User' parameter in the Account table overrides
this parameter (see 'Configuring Account Table' on page

Trunk Group Name

[TrunkGroupSettings_TrunkGro
upName]

Defines a name for the Trunk Group. This name represents the
Trunk Group in the SIP 'tgrp' parameter of the outgoing INVITE
messages (according to RFC 4904). For example:

sip:+16305550100;tgrp=

TG-1

;trunk-c1-

[email protected];user=phone

The valid value can be a string of up to 20 characters. By
default, no name is configured.

Notes:



If this parameter is not configured, the Trunk Group decimal
number is used in the SIP 'tgrp' parameter.



This feature is enabled by any of the following parameters:



UseSIPtgrp



UseBroadsoftDTG



Currently, this parameter can only be configured using the ini
file.

«
...
238
239
240
241
242
...
»

Содержание Media Pack MP-11x











































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Media Pack MP-11x

Бренд: Pathport Страницы: 3

Бренд: TCS Страницы: 56

Бренд: TRENDnet Страницы: 4

Modular IoT Gateway

Бренд: Volansys Страницы: 26

Бренд: New Rock Technologies Страницы: 75

Бренд: Stahl Страницы: 64

Бренд: Kunbus Страницы: 30

Бренд: Alcatel-Lucent Страницы: 2

Бренд: Gree Страницы: 31

Бренд: Hewlett Packard Enterprise Страницы: 26

Бренд: Hitron Страницы: 124

TotalStorage NAS Gateway 500

Бренд: IBM Страницы: 358

Бренд: RTA Страницы: 66

Бренд: Ubee Страницы: 101

Бренд: Avaya Страницы: 2

Бренд: RTA Страницы: 76

Бренд: RTA Страницы: 83

NeoGate TG Series

Бренд: Yeastar Technology Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды