Atmos A45 Скачать руководство пользователя | Manualshive

Страница: 50 / 64

background image

G

B

www.atmos.cz

50-GB

Operation and Maintenance Manual - GB

If we are going to control the pump in the boiler circuit (recommended S14 = 12 or S14 = 13),
we must always connect the TK sensor.

• Fan speed -

displays the

current speed of the fan

• Fan speed 2 –

displays the

current speed of fan 2 (not used)

• Conveyor -

displays the

current status of the conveyor

• Conveyor faults -

displays

information for the service engineer

• Spirals -

displays

the current status of the ignition spirals

• Spiral faults -

displays

information for the service engineer

• Reserve R -

displays the

current status of the reserve output R (parameter S6)

• Reserve R2 -

displays the

current status of the reserve output R2 (parameter S14)

TESTING menu

• Autotest

– This function is used for automatic testing of all the basic elements of the burner as the

fan, conveyor, ignition spirals, etc. The testing is carried out consecutively in 20-second intervals
so that the engineer can monitor the operation of individual devices. If this test is not sufficient,
individual devices can be run separately, namely with the use of the following functions.

CAUTION

– During testing the burner is put out of operation, therefore before the start of

testing always let the burner properly burn out

with the use the STOP command.

• Fan

- this function is used to test the operation of the fan

• Conveyor

- this function is used to test the operation of the conveyor

• Spiral 1

- this function is used to test the operation of the ignition spiral 1

• Spiral 2

- this function is used to test the operation of the ignition spiral 2

• Reserve R

– this function is used to test the switching device (relay) of the reserve output R

• Reserve R2

– this function is used to test the switching device (relay) of the reserve output R2

• Photocell

- used to test the photocell. Conduct the test by observing its sensitivity when it is

inserted in the burner or outside the burner in the natural light (never on the sun – will cause an
alarm).

«
...
48
49
50
51
52
...
»

Содержание A45

































































Отзывы:

Нет отзывов

Похожие инструкции для A45

Бренд: Riello Страницы: 28

Бренд: Riello Страницы: 44

Бренд: Riello Страницы: 20

Бренд: baltur Страницы: 96

Бренд: Weishaupt Страницы: 72

ISOKERN ISOFLAME ISF24LB

Бренд: EarthCore Страницы: 23

Бренд: baltur Страницы: 60

Бренд: Unigas Страницы: 99

Junior Pro 1 J10

Бренд: Oilon Страницы: 44

ISF-SBVT24VE(N,P)

Бренд: EarthCore Страницы: 28

Бренд: Unigas Страницы: 132

Бренд: Lamborghini Caloreclima Страницы: 64

Бренд: Conrad Страницы: 2

Бренд: baltur Страницы: 60

Turbojet 5964 098 490

Бренд: Würth Страницы: 56

Бренд: CROWN VERITY Страницы: 8

Бренд: BiSolid Страницы: 36

Бренд: Grand Canyon Gas Logs Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды