Associated Research HYAMP II 5030DT Скачать руководство пользователя | Manualshive

Страница: 51 / 53

background image

CALIBRATION

47

Please use the numerical keys to enter the reading from the ac voltmeter into the
instrument. Then press the “Enter” key to store the voltage setting. If an incorrect value is
entered, press the “EXIT” key. Then the correct value may be re-entered.

2. Calibration of Current

Equipment needed: STANDARD AC AMMETER with a range of 30A.

Please connect the standard ac ammeter across the output leads of the instrument. Press
the “1” key. The instrument will provide around 30A on the output and the display will
show:

C u r r e n t = __ A

Please use the numerical keys to enter the reading of the standard ac ammeter into the
instrument. Then press the “Enter” key to store the current setting. If an incorrect value
is entered, press the “EXIT” key. The correct value may be re-entered.

3. Setup of the Password and Lock Function

Please refer to the setup procedures section of this manual.

4. Exit Calibration Mode

After the calibration is complete, turn the input power switch to OFF (0) to exit the
Calibration Mode. Turn the power switch to ON (|) to return to standard operating test
mode for calibration verification.

«
...
49
50
51
52
53
»

Содержание HYAMP II 5030DT






















































Отзывы:

Нет отзывов

Похожие инструкции для HYAMP II 5030DT

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 8

Бренд: AAON Страницы: 36

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: JBL Страницы: 17

Бренд: Alpina Страницы: 24

Бренд: Bird-X Страницы: 2

Бренд: CombiSteel Страницы: 60

Бренд: Lightolier Страницы: 2

Бренд: GGM gastro Страницы: 3

Бренд: Wartmann Страницы: 56

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

Бренд: e. Beckmann Страницы: 12

Бренд: Rottler Страницы: 96

Бренд: WIFO Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды