Associated Research HYAMP II 5030DT Скачать руководство пользователя | Manualshive

Страница: 35 / 53

background image

OPERATION

31

Please use the “Numerical” keys to enter the four numeral password and then press the
“Enter” key to exit and return to the test mode. If the current position of the lock
function is “OFF”, the status will be changed to “ON” and the “Lock” indicator on the
front panel will be illuminated. In the reverse case, the status will be changed to “OFF”
and the “Lock” indicator will be off.

8.

To setup the Remote Control, LCD Contrast, and Alarm Volume

(A). Status of Remote Control setting
Press the “UP” or “DOWN” arrow key to toggle the programs until the display shows:

R e m o t e = ON

or

R e m o t e = OFF

Press the “Enter” key to select the “ON” or “OFF” function of the Remote Control mode,
the display will show the status immediately. Press the Exit key to exit to the test mode or
toggle to another setting using the arrow keys. If the Remote Control is set to “ON”, the
“Test” function will be controlled by the “Remote Control” via the remote connectors
located on the rear panel. The “Test” switch on the front panel is locked out, but the
“Reset” switch will still be functional. If the Remote Control is set to “OFF”, the
operation will be controlled by the “Test” and “Reset” switches on the front panel.

(B). LCD Contrast setting
Press the “UP” or “DOWN” arrow keys to toggle the programs to the display shown:

C o n t r a s t = X

Please use the “Numerical” keys to enter the range of Contrast, from “0” to “9”. Then
press the “Enter” key to store the Contrast range. A total of 10 ranges are available. The
LCD will change the Contrast immediately and the display will show the set value on the
screen. The Contrast number “0” is the weakest and “9” is the strongest. Toggle the
arrow keys to another setting or press the “Exit” key to exit from the setting mode and
enter the testing mode.

(C). Alarm volume setting
Press the “UP” or “DOWN” key to toggle the programs until the display shows:

B u z z e r = X

«
...
33
34
35
36
37
...
»

Содержание HYAMP II 5030DT






















































Отзывы:

Нет отзывов

Похожие инструкции для HYAMP II 5030DT

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренд: ICP DAS USA Страницы: 45

Бренд: olympia electronics Страницы: 4

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

FLEX-FOOT ASSURE

Бренд: Össur Страницы: 82

Бренд: Össur Страницы: 32

Digital Measuring System forUnloader & CTi CM...

Бренд: Össur Страницы: 6

DH Offloading Post-Op StyleShoe

Бренд: Össur Страницы: 32

Бренд: Össur Страницы: 65

Бренд: Össur Страницы: 92

Бренд: Össur Страницы: 38

TITAN 2967-033A

Бренд: Yetter Страницы: 20

Spielturm Premium L GP1122

Бренд: gartenpirat Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды