Associated Research HYAMP II 5030DT Скачать руководство пользователя | Manualshive

Страница: 32 / 53

background image

OPERATION

28

2. To set the output test voltage

Please press the “VOLTAGE” key, the display will show:

V o l t a g e = X.XX V

Use the “Numerical” keys to enter the voltage setting, then press the “Enter” key to store
the setting. The unit of measure is in volts with 3.00 - 8.00 being the range.

3. To set the high limit resistance trip setting

Please press the “HI-LIMIT” key, the display will show:

HI-LMT = XXX m

Ω

Please use the “Numerical” keys to enter the high limit resistance trip setting, then press
the “Enter” key to store the setting. The unit of measure is in milliohms with a range from
0-600 m

Ω

’s.

4. To set the low limit resistance trip setting

Please press the “LO-LIMIT” key, the display will show:

LO-LMT = XXX m

Ω

Please use the “Numerical” keys to enter the low limit resistance trip setting, then press
the “Enter” key to store the setting. The unit of measure is in milliohms with a range from
0-600 m

Ω

’s, if set for “0”, the low limit resistance trip setting will be disabled.

5.

To set the dwell time

Please press the “DWELL” key the display will show:

Dwell - T = XXX . X s

Use the “Numerical” keys to enter the dwell time setting, then press the “Enter” key to
store the dwell time setting. The range is 0 to 999.9 seconds, if the dwell time is set to
“0”, the instrument will operate in a continuous ON mode when the test button is

«
...
30
31
32
33
34
...
»

Содержание HYAMP II 5030DT






















































Отзывы:

Нет отзывов

Похожие инструкции для HYAMP II 5030DT

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренд: Pablo Страницы: 7

Бренд: olympia electronics Страницы: 4

Бренд: V.ORLANDI Страницы: 144

Бренд: Lalizas Страницы: 12

BOBCAT 130 Series

Бренд: Balcrank Страницы: 12

Бренд: Xtricity Страницы: 4

Бренд: Dräger Medical Страницы: 92

Бренд: Gfp Страницы: 14

Бренд: SUHNER MACHINING Страницы: 30

Бренд: Kettler Страницы: 20

Porta PlumeSafe 604

Бренд: Buffalo filter Страницы: 75

Бренд: Hettich Страницы: 104

Shark Beam FX one

Бренд: SHOWTEC Страницы: 32

Бренд: P.Lindberg Страницы: 10

Бренд: Klus Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды