manualshive.com logo in svg

Associated Research HYAMP II 5030DT, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Associated Research HYAMP II 5030DT Скачать руководство пользователя страница 16

 

WHAT’S NEW

 

 

 

12

WHAT’S NEW IN HYAMP II 

 

STORAGE OF UP TO 10 DIFFERENT TEST SETUPS 

Allows users who test many different products to access various test setups 
through the keypad or through PLC remote. 

 
MICROPROCESSOR CONTROLLED 

The easy to follow menu screens ensure that the user will set all parameters 
through the keypad correctly. 

 
PLC REMOTES 

Two 9 pin interfaces provide the user with all the necessary remotes required to 
configure HYAMP II through simple PLC control.  Outputs include Pass, Fail, Test 
in Process and Reset out.  Inputs include Test, Reset and Withstand Processing.  
Remote recall of memory programs 1-3. 

 

 
DWELL TIMER COUNTDOWN 

The countdown timer allows the user to clearly see how much time is left on the 
test. 

 
TAMPER-PROOF CONTROLS 

With the user programmable password, access to setup screens can be limited to 
authorized personnel only. 

 
METER MEMORY 

This standard feature holds results of failed tests on the LCD, allowing the user to 
further review test results. 

 
HIGHER OUTPUT CURRENT 

Increased output current of 31 Amps allows the HYAMP II to meet safety agency 
requirements.   

 
FRONT PANEL LCD WITH ADJUSTABLE DIMMER

 

HYAMP II utilizes an enhanced LCD to display setups and test results.  For easier 
reading of the screen, the user can set the contrast to 10 different levels using the 
keypad. 

 
ALARM VOLUME CONTROL 

The user can change the volume of the failure alarm to fit a variety of  
environments.

 

 
FREQUENCY SELECTION 

This feature allows the user to toggle between 50hz and 60hz so products can be 
tested at the same frequency they will be used at. 

 
 

Содержание HYAMP II 5030DT






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды