Anritsu 3656B W1 Скачать руководство пользователя страница 157

Страница: 157 / 278

Using the 2300-584-R Software with the ME7838E4

5-5 Running the Verification Software

3656B W1 Cal/Ver Kit & 2300-584-R PVS UG

PN: 10410-00286 Rev. L

5-7

Click

to continue. The program searches for the GPIB Board in the PC Controller that is set to GPIB

Address 6 and displays a confirmation dialog.

Click

Yes

to continue. Click

to search for another GPIB Board.

Yes

was clicked, the program searches for a compatible VNA on the GPIB. When the VNA is found, a

confirmation dialog box appears.

Click

Yes

to continue, or click

to search for another VNA.

Yes

is clicked above, the program searches for the BB/mm Modules and, when found, requests the

model number and the serial number of the test set and each module.

Figure 5-8.

GPIB Board Dialog

Figure 5-9.

Found Instrument Dialog

Note

If your system is configured with a Lightning 37000 series VNA, refer to

Chapter 7, “2300-584-R

Software with the Lightning ME7808A/B/C”

Содержание 3656B W1























































































































































































































































































Результаты поиска

Содержание 3656B W1

Отзывы:

Anritsu 3656B W1, Руководство пользователя, Страница: 157 / 278

Результаты поиска

Содержание 3656B W1

Отзывы: