Anmax CM-520 Скачать руководство пользователя страница 153

Страница: 153 / 348

Enter 137 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-3-1-4.

Set Composite Triggers Functionality

Some supplementary functions are necessarily executed by using composite triggers

though Scan Button primarily serves to scan barcodes, and Small Trigger to initiate data

transmission. In Memory mode, all the scanned barcode data will be deleted by pressing

small trigger and Scan button in a specified sequence described below: while holding the

smaller till the orange LED light starts flashing rapidly, press down Scan button at the

same time and then release both buttons. Scan the appropriate label to enable or disable

functionality of file deletion.

7-3-1-5.

Enable/Disable Battery Charge

Scan the appropriate barcode to determine whether to initiate battery charge whenever the

device is well connected to host PC using an interface cable and switched to Memory

mode.

7-3-1-6.

Set Good Read Buzzer Volume

Scan the appropriate barcode to specify the volume of Good Read Buzzer when a barcode

is decoded successfully. The higher level indicates the louder sound.

*BE293*

Normal

BE293

*BE280*

Disable

BE280

*BE281*

DelAll

BE281

*BE292*

Mem Tx

BE292

*BE300*

Disable

BE300

*BE301*

Enable

BE301

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды