Anmax CM-520 Скачать руководство пользователя страница 182

Страница: 182 / 348

Enter 166 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-4-1-11.

Set ACK timeout for SPP

ACK timeout refers to the allotted time to elapse for the receipt of ACK signal before

timeout is initiated. This parameter allows you to specify the amount of time allocated for

ACK timeout if the associated operations are performed using RS-232 or USB COM

interfaces.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BtSppTxAckTime

barcode to configure ACK timeout for SPP.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal values

barcodes representing the desired value in the range of 2 to 255. For instance, to set

ACK timeout to be 3 seconds, then scan

to assign the specified decimal value

“3”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

7-4-1-12.

Set Caps Lock setting for HID

This parameter provides the alternative to emulate Caps Lock which is a lock key to

change the letter case of the typed alphabets. Read either

Caps Lock On

Caps Lock

off

label to initiate the inversion of the letter case. However, in this case, the status of

Caps Lock on your physical keyboard should be also taken into account. As to the mutual

interaction between Caps lock key on the keyboard and the capital settings, please refer to

the below chart to achieve the attempt. However, in addition to the two options mentioned

earlier, there are one more alternatives for you to choose from as well: Scan

Alt+Keyoad

label to determine the letter case of typed alphabets by keystroke combinations of Alt +

ASCII code , regardless of the status of Caps Lock key.

*AEAE0*

BtSppTxAckTime

AEAE0

ABCdef

ABCdef

(Length: 1 digit / Range: 2-255/ Unit: 1000ms)

Example

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды