Anmax CM-520 Скачать руководство пользователя страница 158

Страница: 158 / 348

Enter 142 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-3-1-18.

Enable/Disable Footer Info

Scan the appropriate barcode to determine whether or not to transmit footer information

as part of transmitted data in Memory mode.

7-3-1-19.

Set Good Read Buzzer Frequency

Please follow the below steps to specify the buzzer frequency when a barcode is decoded

successfully.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BzGoodRdFreq

barcode to configure Good Read buzzer frequency.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal

values barcodes representing the desired value in the range of 0 to 255. For

instance, to set Good Read buzzer frequency to 10000 Hz, scan

1, 0,

and then

assign the specified decimal value “100”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

7-3-1-20.

Set Good Read Buzzer Duration

Please follow the below steps to specify buzzer duration when a barcode is decoded

successfully.

*BE770*

Disable

BE770

*BE771*

Enable

BE771

*BF8E0*

BzGoodRdFreq

BF8E0

*BF9E0*

BzGoodRdTime

BF9E0

(Length: 1 digit / Range: 0-255/ Unit: 100Hz)

(Length: 1 digit / Range: 0-255/ Unit: 10ms)

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды