Anmax CM-520 Скачать руководство пользователя страница 32

Страница: 32 / 348

Enter 16 End

*/$%ENTR* *ZEND*

Knowing your Scanner

3-2.

LED & Beeper indications

LED and Beeper signals both serve to deliver visual or acoustic messages regarding the

status of the ongoing operation. Either color changes or sound pitches and melodies will

suffice to indicate a scan result as advance notification. Please refer to the below chart to use

LED and Beeper indications for your benefit while working on the device.

Functions

Beeper Sequence

LED indication

Power on the scanner

Successfully decode a barcode

Green LED flashes once

Successfully scan a regular

setup barcode

high-low tone

Successfully scan a special

setup barcode

High-low-high-low notes

Successful enter configuration

mode

A set of five ascending notes

Red, green, and then blue

LEDs keep flashing slowly and

alternatively

Successfully enter firmware

update process

After One high tone emit five

quick short notes followed by a

pause and then two notes.

Red and green LEDs keep

flashing slowly and

alternatively

Complete scanner

configuration

A melody from high notes to

low ones

Switch to data-transmission

mode

One high note followed by two

low short notes

The orange LED keeps

flashing rapidly.

Successful attempt to transmit

all the data

One long beeping note sings

first, and then a short note

sounds after data is

transmitted.

Charging Attempt

A solid red LED indicates the

ongoing charge process. Once

the charging is completed, the

red LED will start flashing

slowly as a full battery charge

indication.

Unknown Failure

Red LED flashes once as a

warning.

Timeout for configuration

mode

Two ascending notes and then

three descending notes

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды