Anmax CM-520 Скачать руководство пользователя страница 186

Страница: 186 / 348

Enter 170 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-4-1-17.

Set Time Delay for a Record for HID

This parameter refers to the amount of elapsed time to delay transmitting a record. Please

follow the below steps to set time delay for transmitting a record if the associated

operations are performed using USB HID interfaces.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BtHidTxCharGapTime

barcode to configure delay time for a digit for HID.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired value in the range of 0 to 255. For instance, to

defer transmitting a digit for 0.2 seconds, scan

2, 0

and then

to assign the specified

decimal value “200”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BtHidTxGapTime

barcode to configure delay time for a record for HID.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired value in the range of 0 to 255. For instance, to

defer transmitting a digit for 0.2 seconds, scan

first and then

to assign the

specified decimal value “20”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

*AFFE0*

BtHidTxGapTime

AFFE0

(Length: 1 digit / Range: 0-255/ Unit: 10ms)

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды