Anmax CM-520 Скачать руководство пользователя страница 94

Страница: 94 / 348

Enter 78 End

*/$%ENTR* *ZEND*

Editing General Settings

6-2-9.

Enable/Disable Vibrator for Confgiruration Mode

This special vibrator will send a vibration signal as a warning indicator when configuration

mode is initiated by a scan on

Enter

label. Scan the appropriate barcode to have the feature

disabled or enabled.

6-2-10.

Enable/Disable Header

Headers refer to additional information, including serial number, date, time and so on, which

precedes the decoded message while saved barcodes are transmitted in Memory mode. Scan

the appropriate barcode to determine whether or not to send out the header information as

part of transmitted data.

6-2-11.

Enable/Disable Serial Number Info in the Header

Scan the appropriate barcode to determine whether or not to send out serial number

information as part of header information.

*A4600*

Disable

A4600

*A4601*

Enable

A4601

*A4610*

Disable

A4610

*A4611*

Enable

A4611

*A4570*

Disable

A4570

*A4571*

Enable

A4571

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды