Anmax CM-520 Скачать руководство пользователя страница 111

Страница: 111 / 348

Enter 95 End

*/$%ENTR* *ZEND*

Setting up your Operation Modes

7-2.

Cable Mode

Please be advised the following parameters in this section simply work for the associated

operations in Cable mode. Make sure that you appropriately conduct the operations using

Cable mode.

7-2-1.

Output Interface Options

In terms of output interface options, it is more about technical configuration regarding

how you want barcode data to be transmitted between devices in Cable mode before

scanned barcode is further processed. Properly configure your scanner according to the

realistic situation will lead to satisfactory data transmission performance.

7-2-1-1.

Set Data Transfer Rate for SPP

Data transfer rate, measured in bits per second, refers to speed of digital data travelled

among devices. Scan the appropriate barcode to specify data transfer rate for SPP if the

associated operations are performed using RS-232 or USB COM interfaces.

7-2-1-2.

Set Length of Stop Bit for SPP

Stop bit follows after the end of data in transit as to signal the end of transmitted data.

Scan the appropriate barcode to specify the length of stop bit for SPP if the associated

operations are performed using RS-232 or USB COM interfaces.

*AA020*

7 Bits

AA020

*AA021*

8 Bits

AA021

*AA030*

1 Bit

AA030

*AA031*

2 Bits

AA031

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды