Anmax CM-520 Скачать руководство пользователя страница 260

Страница: 260 / 348

Enter 244 End

*/$%ENTR* *ZEND*

Configuring Symbology

8-8.

Industrial 2 of 5

8-8-1.

Enable/Disable Industrial 2 of 5

Scan the appropriate barcode to determine whether or not to enable Industrial 2 of 5.

8-8-2.

Configure Checksum Type

Checksum type determines the checksum algorithm which serves to detect if an error occurs

during the decoding process. Scan the appropriate barcode to examine whether or not the

barcode cantinas the check digit and to further apply the related error detection mechanism

to the scanned data.

8-8-3.

Transmit Check Digit

Scan the appropriate barcode to determine whether to transmit the check digit.

8-8-4.

Truncate Leading Zeros

Scan

Enable

label to shrink the barcode message by getting rid of leading zeros.

*E0001*

Enable

E0001

*E0000*

Disable

E0000

*E0181*

Enable

E0181

*E0180*

Disable

E0180

*E0070*

Disable

E0070

*E0071*

Enable

E0071

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды