Anmax CM-520 Скачать руководство пользователя страница 101

Страница: 101 / 348

Enter 85 End

*/$%ENTR* *ZEND*

Editing General Settings

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BarWaitAddonCnt

barcode to configure the length of the timeout session.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired decimal value in the range of 0 to 255. For

instance, to set timeout period to 1 second, then scan

to assign the specified

decimal value “1”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

6-2-24.

Set Count of Barcode Verification

There are some occasions in which you will have to compromise on scanning speed in

exchange for scanning accuracy. The parameter allows you to specify the number of times

the barcode verification process will be executed before the decoded scanned data is

transmitted. The barcode will be identified as a valid one when the same decoded result is

always returned every time. As mentioned earlier, it likely takes longer to decode a barcode

with higher accuracy. For your reference, to ensure the authentication is performed at the

specified count of execution, it is necessary to enable

DblConFirmSw

parameter for each

operation mode at the same time.

Procedure

(1)

Scan

Enter

barcode.

(2)

Scan

BarDblConfirmCnt

barcode to configure the length of the timeout session.

(3)

Please refer to Decimal/Hexadecimal Table in the appendix to scan decimal value

barcodes representing the desired decimal value in the range of 0 to 255. For

instance, to set timeout period to 1 second, then scan

to assign the specified

decimal value “1”.

(4)

Scan

SET

barcode to complete the variable-binding operation.

(5)

Scan

End

barcode to complete the configuration.

(Length: 1 digit / Range: 0-255)

(Length: 1 digit / Range: 1-10)

*A58E0*

BarWaitAddonCnt

A58E0

*A59E0*

BarDblConfirmCnt

A59E0

Содержание CM-520





























































































































































































































































































































































Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды

Anmax CM-520, Руководство пользователя

Результаты поиска

Содержание CM-520

Отзывы:

Похожие инструкции для CM-520

Бренды по названию

Популярные бренды