Analog Devices ADuCM320 Скачать руководство пользователя страница 14

Страница: 14 / 196

UG-498

ADuCM320 Hardware Reference Manual

Rev. C | Page 14 of 196

Clock Dividers Register

Address: 0x40028004, Reset: 0x0200, Name: CLKCON1

Table 6. Bit Descriptions for CLKCON1

Bits

Bit Name

Description

Reset

Access

[15:12]

RESERVED

Reserved.

0x0

CDD2DCLK

D2DCLK divide bits.

0x0

0: D2D_CLK frequency = HCLK frequency.

1: D2D_CLK frequency = half of HCLK frequency.

[10:8]

CDPCLK

PCLK divide bits. PCLK divide bits.

0x2

000: reserved.

001: reserved.

010: DIV4. Divide by 4 (PCLK is quarter the frequency of root clock,
20 MHz). All ADC specifications are based on this setting. Using any other
setting may affect ADC performance.

011: DIV8. Divide by 8.

100: DIV16. Divide by 16.

101: DIV32. Divide by 32.

110: DIV64. Divide by 164.

111: DIV128. Divide by 128.

[7:3]

RESERVED

Reserved. Always returns 0 when read.

0x0

[2:0]

CDHCLK

HCLK divide bits.

0x0

000: DIV1. Divide by 1 (HCLK is equal to root clock).

001: DIV2. Divide by 2 (HCLK is half the frequency of root clock).

010: DIV4. Divide by 4 (HCLK is quarter the frequency of root clock).

011: DIV8. Divide by 8.

100: DIV16.Divide by 16.

101: DIV32.Divide by 32.

110: DIV64.Divide by 64.

111: DIV128. Divide by 128.

User Clock Gating Control Register

Address: 0x40028014, Reset: 0x0040, Name: CLKCON5

The user clock gating control register (CLKCON5) is used to control the gates of the peripheral UCLKs.

Table 7. Bit Descriptions for CLKCON5

Bits

Bit Name

Description

Reset

Access

[15:7]

RESERVED

Reserved. Always returns 0 when read.

0x0

RESERVED

Reserved. Always set to 1.

0x1

UCLKUARTOFF

UART clock user control. This bit disables the UCLK_UART clock. It controls

the gate on UCLK_UART in Power Mode 0 and Power Mode 1. In Power Mode 2
and Power Mode 3, the UCLK_UART is always off and this bit has no effect.

0x0

0: clock on

1: clock off

UCLKI2C1OFF

I2C1 clock user control. This bit disables the PCLK_I2C1 clock. It controls

the gate on PCLK_I2C1 in Power Mode 0 and Power Mode 1. In Power Mode 2
and Power Mode 3, the I2C1 PCLK is always off and this bit has no effect.

0x0

0: clock on

1: clock off

UCLKI2C0OFF

I2C0 clock user control. This bit disables the PCLK_I2C0 clock. It controls

the gate on PCLK_I2C0 in Power Mode 0 and Power Mode 1. In Power Mode 2
and Power Mode 3 the PCLK_I2C0 is always off and this bit has no effect.

0x0

0: clock on

1: clock off

RESERVED

Reserved.

0x0

Содержание ADuCM320





































































































































































































Результаты поиска

Содержание ADuCM320

Отзывы:

Похожие инструкции для ADuCM320

Бренды по названию

Популярные бренды

Analog Devices ADuCM320, Справочник по аппаратуре

Результаты поиска

Содержание ADuCM320

Отзывы:

Похожие инструкции для ADuCM320

Бренды по названию

Популярные бренды