Appendix B - Wireless Technology
188
10" Modero Touch Panels
How to Upload a Certificate File
1.
Install the latest AMX USB LAN LINK driver onto your computer by installing the latest versions of
either TPDesign4 or NetLinx Studio2. This USB driver prepares your computer to properly communicate
with a directly connected G4 touch panel (MVP/CV7/CV10).
Refer to Step 1 from within the previous
Step 1: Setup the Panel and PC for USB
Communication
section on page 186.
2.
Access the target panel's Protected Setup firmware page and configure the USB communication
parameters.
Refer to Step 2 from within the previous
Step 2: Confirm the Installation of the USB Driver on the
PC
section on page 186.
3.
With the panel successfully communicating with target computer, launch the Certificate Upload Utility.
Familiarize yourself with the User Interface options (Certificate Utility User Interface).
4.
Locate your certificate file by using the
Browse
button and navigating to the desired file type.
5.
Use the drop-down arrow in the
Local Address
field to select communication through either the
computer's Ethernet port (Internet communication) or via the USB port (direct connection). If using an
Ethernet connection skip to step 8.
6.
For a USB connection
, select the
10.XX.XX.1
IP Address which corresponds to the virtual IP Address
assigned to the USB connection port on the computer.
7.
For a USB connection
, navigate to the
Add IP Address
field (bottom-right of the interface) and enter a
value of
1
greater than the virtual USB IP Address.
For example: If the virtual USB IP Address is
10.0.0.1
then you would add an address for the
directly connected panel of
10.0.0.2
(this is one greater than the USB address value detected by the
utility).
You can send a certificate to ONLY ONE directly connected panel (via USB)
. If using the
Ethernet port's IP Address, you can send a server certificate to multiple target panels.
8.
For an Ethernet IP Address connection
, select the IP Address which corresponds to the local
computer's Ethernet address.
9.
Navigate to the
Add IP Address
field (bottom-right of the interface) and enter the IP Addresses of the
various target touch panels.
10.
Click the
Add
button to complete the entry and add the new IP Address to the listing of available device
IP Addresses. Repeat this process for all subsequent device IP Addresses.
11.
Once your list is complete, click on the
File
drop-down menu and select the
Save
option to launch a Save
dialog where you can assign a name to the current list of addresses and then save the information (as a
TXT (text) file) to a known location.
12.
Select the target devices which be uploaded with the selected certificate. These can either be:
individually selected by toggling the box next to the Send entry (with the Type column).
selected as a group by clicking on the Check All radio box located at the top of the device IP
Address listing.
13.
When you are ready to send the certificate file to the selected panels, click the
Send
button to initiate the
upload.
Once the
Status
field for each entry reads
Done
, your upload was successfully completed.
This application must be run from a local machine and should not be used from a
remote network location.
Содержание modero NXD-CV10
